产品详情
产品描述
偏心套的作用
为降低成本和减小加工难度，我们常在轴承孔处采用偏心套。壳体的孔加工完成后
与其相清烂对位置就确定了，加入偏心套后，当齿搏悄轮或壳体存在加工和装配误差时，通过转动偏心套可答银漏调节两齿轮之间侧隙，能消除
齿厚偏差、中心距的偏差和公法线偏差，偏心套的引入不仅降低了壳体孔系的位置精度、齿轮螺旋角精度的加工要求，控制了回差。
免责声明丨 部分内容来源网络！本文仅供交流学习 , 版权归属原作者，部分图片、内容推送时未能及时与原作者取得联系，若来源标注错误或侵犯到您的权益烦请告知，我们将立即删除.
公司供应摊铺机配件，压路机配件，铣刨机配件，摊铺机刮板驱动轴，刮板驱动轴总成，找平仪，找平仪支架以及液压泵和配件。还供应摊铺机易损件，摊铺机平衡梁，搅龙轴，踏板，输料底板，叶片，熨平板，减速机，链轨，履带板，支重轮，刮板大链条，输料链条等。
联系人：梁经理
联系方式：13645201509
（微信同号）
QQ：2870202745
QQ邮箱：2870202745@qq.com
网易邮箱：LS13645201509@163.com
The function of eccentric sleeve
To reduce costs and machining difficulties, we often use eccentric sleeves at the bearing holes. After the hole machining of the shell is completed
The position is determined by comparing the two gears. After adding the eccentric sleeve, when there are machining and assembly errors in the gear or housing, the side clearance between the two gears can be adjusted by rotating the eccentric sleeve, which can eliminate them
The introduction of eccentric sleeves not only reduces the positional accuracy of the shell hole system and the machining requirements for gear helix angle accuracy, but also controls backlash due to deviations in tooth thickness, center distance, and common normal line.
Disclaimer | Some content is sourced from the internet! This article is for communication and learning purposes only. The copyright belongs to the original author. Some images and content were not promptly contacted when pushed. If the source annotation is incorrect or infringes on your rights, please inform us and we will immediately delete it
Company Introduction
The company supplies paver accessories, roller accessories, milling machine accessories, paver scraper drive shaft, scraper drive shaft assembly, leveling instrument, leveling instrument bracket, hydraulic pump and accessories. We also supply vulnerable parts for pavers, including balance beams, agitator shafts, pedals, feeding base plates, blades, ironing plates, reducers, chain rails, track plates, support wheels, scraper chains, and feeding chains.
Contact: Manager Liang
Contact information: 13645201509
(Same WeChat account)
QQ：2870202745
QQ email: 2870202745@qq.com
NetEase email: LS13645201509@163.com
免责声明：
本页产品如有侵权请联系我们进行删除处理！联系电话：18705218934
rp952摊铺机配件与维修,欢迎您的光临!
联系人:梁经理
联系手机:13645201509
* 表示必填采购：ABG525偏心轴套 #2190903
*联系人：
请填写您的姓名，方便我们联系您
*手机号码：
请填写您的手机号码
电子邮箱：
请填写您的电子邮件
备注：